Free tool · Writing tools
Morse code translator
Type text to get Morse code, or paste dots and dashes to read them. Play the result as sound at the speed you choose. Nothing you enter leaves your device.
- Free
- No sign-up
- Runs in your browser
- 7 characters encoded
- Lines
- 1 before, 1 after
- Characters
- 8 before, 30 after
- Audio length
- 5.7 s
How to use the Morse Code Translator
- Choose Text to Morse or Morse to text under Translate.
- Type or paste into Your text. The translation appears under Result as you type.
- Press Play sound to hear it. Change the speed under Audio speed, and use Stop to cut it short.
- Press Copy to copy the result.
How do I translate text to Morse code?
Each letter, digit and common punctuation mark has its own pattern of short signals (dots, also called dits) and long signals (dashes, also called dahs). Type your message and the tool looks up every character in the international Morse table. In the result, the letters of a word are separated by a single space and words are separated by a slash: "SOS help" becomes ... --- ... / .... . .-.. .--..
The tool covers the 26 letters, the digits 0 to 9, and these signs: . , : ? ' - / ( ) " = + @. Capital and small letters give the same code. Anything else, such as an accented letter or an exclamation mark, has no sign in the international table, so it is skipped and listed below the result. Line breaks in your text are kept, so each line is translated on its own line.
What is the Morse code for SOS, and how do I read Morse?
SOS is three dots, three dashes, three dots: ... --- .... It is the best-known distress signal because it is easy to send and hard to mistake, not because the letters stand for words. Read Morse by splitting it into letters at the spaces, then looking each group up: .- is A, -... is B, . is E and - is T.
Switch to Morse to text and paste your dots and dashes. Put a single space between letters and a slash between words. A gap of three or more spaces also counts as a word break. Typographic dots and dashes, such as • and –, are accepted. A group that is not a Morse character is shown as a question mark and listed under the result, which usually points to a missing space.
What is the standard timing of dots and dashes?
The international Morse recommendation (ITU-R M.1677-1) fixes the rhythm by counting in dots. A dash lasts three dots. The space between the signals of one letter is one dot, the space between two letters is three dots, and the space between two words is seven dots. The audio here follows exactly those proportions.
The absolute speed is a choice. Speed is measured in words per minute, using the word PARIS as the yardstick, which takes 50 dots to send including the gap that follows it. At 15 words per minute one dot therefore lasts 1.2 / 15 = 0.08 seconds. "SOS help" lasts about 5.7 seconds at that speed; the audio length is shown under the result. The tone is a 600 Hz beep made by your browser, with no sound files. Sound only starts when you press Play sound, because browsers block audio that starts by itself. Slower speeds, such as 5 or 10 words per minute, are easier to learn from.
Use it with
- Case Converter: UPPER, lower, Title, Sentence case.
- Bold Text Generator: bold and italic Unicode for social bios.
- Invisible Character: copy a blank character for names and messages.
Questions
How do I translate text to Morse code?
Choose Text to Morse and type your text. Each letter becomes dots and dashes, letters are separated by a space and words by a slash.
What is the Morse code for SOS?
Three dots, three dashes, three dots: ... --- ...
How do I read dots, dashes and spacing?
A dot is a short signal and a dash a long one, equal to three dots. Put one space between letters and a slash between words. Paste it under Morse to text and the tool reads it for you.
What is the standard timing of dots and dashes?
A dash is three dots. The gap is one dot inside a letter, three dots between letters and seven dots between words, as set by ITU-R M.1677-1.
Why is my punctuation missing from the Morse?
Only signs in the international table are encoded. An exclamation mark, for example, has no official sign there, so it is skipped and listed under the result.
Why does the sound not play on its own?
Browsers block sound that starts without a tap or click. Press Play sound to start it.
Sources
How this page was made: the tool's results are computed in your browser by the code on this page, using the sources listed above; the explanations were drafted with AI help and checked against the tool's own output.