Maaz Zindani

Loading the index…

↑↓ move↵ openesc close3993 pages

Free tool · Home and DIY

Concrete calculator

Choose what you are pouring, type the sizes, and get cubic yards or cubic meters plus the bags of premix. Every figure can be changed.

  • Free
  • No sign-up
  • Runs in your browser

By Maaz Zindani · Updated

Units
What are you pouring?
Patio, shed base, driveway or floor slab.
Typical allowance for spills and an uneven base, not a rule: 10.
Result

1.63 yd³ of concrete44.0 ft³ · 1.25 m³ to order, with 10% waste added · 74 bags

  • Slab
  • 10% waste
  • 74 × 80 lb bags at 0.6 ft³
Volume, no waste
1.13 m³
Volume, no waste
1.48 yd³
Volume, no waste
40.0 ft³
To order (with waste)
1.63 yd³
Premix bags (your bag)
74
Bag sizeTypical yieldBags needed
80 lb (36.3 kg)0.60 ft³74
60 lb (27.2 kg)0.45 ft³98
50 lb (22.7 kg)0.375 ft³118
40 lb (18.1 kg)0.30 ft³147
25 kg (55 lb)11.7 L107
20 kg (44 lb)9.4 L133

Formula: volume = length × width × thickness; with waste = volume × (1 + waste ÷ 100); bags = volume with waste ÷ yield of one bag, rounded up. 1 yd³ = 27 ft³.

Your numbers: 12 ft × 10 ft × 0.3333 ft = 40.000 ft³; × (1 + 10 ÷ 100) = 44.000 ft³ = 1.63 yd³; 73.33 bags of 0.6 ft³ rounds up to 74.

Bag yields are typical figures (the 20 and 25 kg yields are scaled from the 80 lb bag, so they are only an estimate); use the yield printed on your own bag. This is a quantity estimate, not structural advice: check the thickness, reinforcement and mix your project needs with your local code or a professional.

How to use the Concrete Calculator

  1. Pick US or Metric under Units, then choose Slab, Footing, Round column or post hole or Steps.
  2. Type the sizes. Each box has its own unit, so you can give the length in feet and the thickness in inches.
  3. Check Waste %, then pick your Premix bag size and correct the Yield of one bag to match the label on your bag.
  4. Read the amount to order and the number of bags under Result, with the formula and your numbers.

How much concrete do I need for a slab?

Multiply length by width by thickness, with all three in the same unit, then divide cubic feet by 27 to get cubic yards. A slab is a box, so that is the whole method.

Example: a slab 12 ft by 10 ft and 4 in thick. Convert the thickness to feet (4 ÷ 12 = 0.3333), then 12 × 10 × 0.3333 = 40 ft³. Divide by 27: 40 ÷ 27 = 1.48 yd³. In metric, a slab 4 m by 3 m and 10 cm thick is 4 × 3 × 0.1 = 1.20 m³, which is 1.57 yd³ because 1 yd³ is about 0.7646 m³.

You do not have to convert anything by hand. Each box has its own unit, so type 4 and choose in beside the thickness. The tool converts to meters internally, so mixed units never cause an error, and it prints the working with your numbers under the result. For an L-shaped or round slab, find the area first with a square footage calculator, then multiply by the thickness.

Concrete for common slab sizes, from the calculator (10% waste added where marked)
SlabVolume at 4 in thickTo order at 4 in, +10%80 lb bags at 4 in, +10%To order at 6 in, +10%
10 x 10 ft33.3 ft³ (1.23 yd³)1.36 yd³622.04 yd³
10 x 12 ft40 ft³ (1.48 yd³)1.63 yd³742.44 yd³
12 x 12 ft48 ft³ (1.78 yd³)1.96 yd³882.93 yd³
12 x 20 ft80 ft³ (2.96 yd³)3.26 yd³1474.89 yd³
16 x 16 ft85.3 ft³ (3.16 yd³)3.48 yd³1575.21 yd³
20 x 20 ft133.3 ft³ (4.94 yd³)5.43 yd³2458.15 yd³

The bag column uses the 80 lb bag at 0.60 ft³ per bag. A thicker slab scales the volume in direct proportion: 6 in is 1.5 times 4 in.

How many bags of concrete make a cubic yard?

Divide the volume by the yield printed on the bag. One cubic yard is 27 cubic feet, so an 80 lb bag that yields 0.60 ft³ needs 27 ÷ 0.60 = 45 bags per cubic yard. The same sum gives 60 bags of 60 lb, 72 of 50 lb and 90 of 40 lb. A 3 ft by 3 ft slab 36 in thick is exactly 1.00 yd³.

The yields the tool starts with are the figures on Quikrete's data sheet for its Concrete Mix: 0.30, 0.375, 0.45 and 0.60 ft³ for the 40, 50, 60 and 80 lb bags. The same sheet gives 0.675 ft³ for a 90 lb bag sold in some regions; type that in Yield of one bag and 27 ÷ 0.675 gives 40 bags per cubic yard. The 20 kg and 25 kg yields in the list are estimates scaled from the 80 lb bag, not published figures, so type the number from your own bag.

Example: the 12 ft by 10 ft slab with 10% waste needs 44 ft³. That is 74 bags of 80 lb, 98 of 60 lb, 118 of 50 lb or 147 of 40 lb. Bags are always rounded up, and 74 bags of 80 lb weigh 5,920 lb before you add water.

Other products and brands can list other yields, so read your bag. The data sheet describes its mix for pouring concrete 2 in (50 mm) thick or more. For a big pour, compare the cost and labor of bags with ready-mixed concrete ordered by the cubic yard; the tool gives the cubic yards to ask for.

Bags per cubic yard and for the 12 x 10 ft, 4 in slab with 10% waste
Bag sizeYield per bagBags per cubic yardBags for the example slab
80 lb (36.3 kg)0.60 ft³4574
60 lb (27.2 kg)0.45 ft³6098
50 lb (22.7 kg)0.375 ft³72118
40 lb (18.1 kg)0.30 ft³90147

How much concrete do I need for a footing, a post hole or steps?

A footing run is also a box: total length × width × depth. Forty feet of footing 16 in wide and 8 in deep is 40 × 1.333 × 0.667 = 35.6 ft³, or 1.32 yd³. With 10% waste that is 39.1 ft³ and 66 bags of 80 lb.

A round column, pier or post hole is a cylinder: π × (diameter ÷ 2)² × height, times the number of holes. A 12 in hole 4 ft deep takes 3.14 ft³, so four of them take 12.6 ft³ (0.47 yd³). Measure the hole, not the post.

For a fence post, the data sheet directs you to dig the hole about 3 times the post's diameter, with a depth of one third of the overall post height, and to follow local building codes for load-bearing posts. A 4 in post that is 8 ft tall overall gives a hole 12 in wide and 32 in deep. The tool counts all 2.09 ft³ of it as concrete, which is 4 bags of 80 lb. The post takes up part of the hole, so the true need is a little lower.

Steps are poured solid from the ground up, so each step is a block as tall as every step below it plus its own rise. Three steps 4 ft wide, with a 7 in rise and an 11 in tread, need width × tread × rise × n × (n + 1) ÷ 2 = 4 × 0.917 × 0.583 × 6 = 12.8 ft³ (0.48 yd³). Add a landing as a separate slab.

How much waste should I add, and how thick should the concrete be?

Waste covers spills, an uneven base and forms that bow, and running short in the middle of a pour is worse than having some left over. The Waste % box multiplies the volume by (1 + waste ÷ 100). On the 12 ft by 10 ft slab, 0% is 1.48 yd³, 5% is 1.56 yd³, 10% is 1.63 yd³, 15% is 1.70 yd³. The tool starts at 10% as an example allowance, not a rule: a flat, well-formed slab may need less, and a rough trench may need more.

The tool estimates quantity only. It does not say how thick a slab should be, or what reinforcement, strength class or base preparation you need. Those depend on the load, the soil and your local building code, so check them with the code or a qualified professional before you pour. A gravel base under the slab is a separate quantity, and the gravel calculator covers it.

Use it with

Questions

How many 80 lb bags of concrete are in a cubic yard?

With a yield of 0.60 ft³ per bag, 27 ÷ 0.60 = 45 bags. The tool uses the yield you type, so use the figure printed on your own bag.

How many bags of concrete do I need for a 10 x 10 slab?

At 4 inches thick a 10 ft by 10 ft slab is 33.3 ft³ (1.23 yd³), so 56 bags of 80 lb with no waste, or 62 with 10% waste. Change the sizes and the tool recounts.

How many cubic yards is a 12 x 10 slab that is 4 inches thick?

40 ft³, which is 1.48 yd³. With 10% waste it is 1.63 yd³.

How do I calculate concrete for a post hole?

Use π × (diameter ÷ 2)² × depth. A 12 inch hole 4 ft deep needs 3.14 ft³, which is 5.2 bags of 80 lb, so 6 bags. Choose Round column or post hole and enter how many holes you have.

Is the bag yield the same for every brand?

No. The tool starts from one manufacturer's published yields for its Concrete Mix and lets you change them. Check the label on the bag you buy.

Does this tell me how thick the concrete should be?

No. It calculates how much you need for the sizes you type. The thickness and reinforcement for your project depend on the load and local code, so check them with a professional.

How this page was made: the tool's results are computed in your browser by the code on this page, using the sources listed above; the explanations were drafted with AI help and checked against the tool's own output.