Maaz Zindani

Loading the index…

↑↓ move↵ openesc close3993 pages

Free tool · Home and DIY

Gravel calculator

Type the area and the depth, pick the material, and get the volume and the weight to order. The density is yours to edit.

  • Free
  • No sign-up
  • Runs in your browser

By Maaz Zindani · Updated

Units
Area to cover
Typical allowance, not a rule: 10. Set 0 for the plain volume.
Result

3.67 tons of gravel2.72 yd³ (73.3 ft³) to order, with 10% extra · 3.33 tonnes · 2.08 m³

  • Crushed stone, 19 mm
  • 200.0 ft²
  • 10% extra
  • 1.35 tons per yd³
Area
200.0 ft² · 18.58 m²
Volume, no extra
2.47 yd³ · 1.89 m³
Volume to order
2.72 yd³ · 2.08 m³
Weight to order
3.67 tons · 3.33 tonnes
DepthTo orderWeight1 ton covers
1 in0.68 yd³0.92 tons240 ft²
2 in1.36 yd³1.83 tons120 ft²
3 in2.04 yd³2.75 tons80 ft²
4 in2.72 yd³3.67 tons60 ft²
6 in4.07 yd³5.50 tons40 ft²

Formula: volume = area × depth; weight = volume × density; to order = × (1 + extra ÷ 100). 1 yd³ = 27 ft³; 1 US ton = 2,000 lb; 1 tonne = 1,000 kg. The table repeats the sum for your area at other depths.

Your numbers: area = 20 ft × 10 ft = 200.00 ft²; × 0.3333 ft deep = 66.67 ft³ = 2.47 yd³; × (1 + 10 ÷ 100) = 2.72 yd³; × 1.35 tons per yd³ = 3.67 tons.

Density is a typical value. It changes with the stone, the grading and how wet the pile is, so use your supplier's figure when you have it.

How to use the Gravel Calculator

  1. Choose US or Metric under Units, then pick how you measure the Area to cover: Rectangle, Circle or I know the area.
  2. Type the sizes and the Depth. Each box has its own unit, so feet and inches can be mixed.
  3. Choose the Material and check the Density box. Type your supplier's figure if you have one.
  4. Set Extra % for compaction and spillage and read the volume and weight under Result.

How much gravel do I need for a driveway or path?

Gravel is bought by volume or by weight, and both start from the same sum: volume = area × depth. A strip 20 ft long and 10 ft wide is 200 square feet. At a depth of 4 inches (0.3333 ft) that is 200 × 0.3333 = 66.7 cubic feet, or 66.7 ÷ 27 = 2.47 cubic yards. In metric, a strip 6 m by 3 m at 10 cm deep is 6 × 3 × 0.1 = 1.8 cubic meters.

For a round bed or circular patio choose Circle and type the diameter; the area is π × (diameter ÷ 2)². If you already know the area from a plan, choose I know the area and type it in square feet, square yards or square meters. The Extra % box then adds an allowance on top: gravel settles when it is compacted, and a little is lost at the edges. With 10% extra the 2.47 cubic yards become 2.72.

How many tons are in a cubic yard of gravel?

It depends on the stone, because weight is volume × density. Crushed stone and pea gravel in the tool start at about 1.35 US tons per cubic yard (2,700 lb, or roughly 1.6 tonnes per cubic meter). Road base or crusher run, which includes fines that fill the gaps, is heavier at about 1.55 tons per cubic yard, and large crushed stone with bigger gaps is lighter at about 1.25. Using 1.35, the 2.72 cubic yards in the example weigh 2.72 × 1.35 = 3.67 US tons, which is 3.33 metric tonnes.

The densities the tool starts from are indicative loose bulk figures published in a trade reference, not a standard, and they are shown in the Density box so that you can overwrite them. They move with the stone, the grading and the moisture content: a wet pile can weigh noticeably more than a dry one. If your supplier quotes tons per cubic yard or tonnes per cubic meter for the material you are buying, type that figure and pick its unit. Changing the unit converts the number instead of changing the density.

How deep should gravel be?

The right depth depends on the use, the ground and the stone size, and this tool does not choose it for you. The table under the result repeats your sum at other depths and adds a column for how far one ton (or tonne) goes: with stone at 1.35 tons per cubic yard, one ton covers 120 square feet at 2 inches and 60 square feet at 4 inches, because a layer twice as deep covers half the area.

For gravel used as decorative ground cover, Mississippi State University Extension lists a layer of about 1 inch. For a driveway, a base under paving or a drainage trench, ask your supplier or a contractor, and follow your local code or the product instructions, because the depth needed depends on traffic loads and soil.

Use it with

Questions

How do I calculate how much gravel I need?

Multiply the area by the depth to get the volume, then multiply by the density to get the weight. For 200 square feet at 4 inches deep that is 66.7 cubic feet (2.47 cubic yards) before extra.

How many tons is a cubic yard of gravel?

About 1.35 US tons for typical crushed stone or pea gravel, but the figure varies from about 1.25 to 1.55 with the material and its moisture. The Density box lets you type your supplier's number.

What is the difference between a ton and a tonne?

A US ton is 2,000 pounds (907 kg) and a tonne is 1,000 kg. The result shows both, so you can read whichever your supplier uses.

How much extra gravel should I order?

The tool starts with 10% for compaction and spillage. That is a rule of thumb: use less for a neat, firm base and more for soft ground or a deep layer.

How much area does one ton of gravel cover?

It depends on depth and density. For stone at 1.35 tons per cubic yard, one ton covers 120 square feet at 2 inches deep and 60 square feet at 4 inches. The table shows it for your density.

How this page was made: the tool's results are computed in your browser by the code on this page, using the sources listed above; the explanations were drafted with AI help and checked against the tool's own output.