Free tool · Audio and video
Tone generator
Type a frequency, choose a waveform and press play. The page shows the nearest note, starts quietly, and fades in. You can also sweep the pitch.
- Free
- No sign-up
- Runs in your browser
- Stopped
- Sine wave
- Both speakers
- Nearest note
- A4, in tune
- One cycle lasts
- 2.273 ms
- Volume
- 10%, about -46 dB below full scale
- Waveform
- a pure tone with one frequency and no overtones
The note names use equal temperament with A4 at 440 Hz. The volume slider is capped: even at 100% the page never sets the output above half of full scale. How loud it really is depends on your device volume, your speakers or headphones and the room. If you hear nothing at a very low or very high frequency, that does not mean your speakers are faulty: small speakers play very low tones poorly, and hearing ranges differ.
How to use the Tone Generator
- Turn your device volume down, then press Play tone. The page starts at 440 Hz and a low volume.
- Type a frequency under Frequency in Hz, move the slider, or press a quick frequency or a note. The pitch changes while it plays.
- Choose a Waveform and the Speaker (both, left only or right only). Raise the Volume slowly.
- For a moving pitch choose Sweep, enter From, To and Seconds, and press play. Press Stop at any time.
How do I play a pure tone at a given frequency?
Type the frequency in hertz (Hz), the number of cycles per second, between 1 and 22,000, and press Play tone. You can write 440, 1.5 kHz or 1,5 with a decimal comma. The slider is logarithmic, so every octave, a doubling of the frequency, takes the same space on it, and the quick buttons jump to 20 Hz, 100 Hz, 440 Hz, 1 kHz, 5 kHz, 10 kHz, 15 kHz and 20 kHz. The tone comes from the oscillator in your browser. It is made on your device, with nothing downloaded or sent anywhere.
A sine wave is the pure tone: one frequency and no overtones. A square wave sounds hollow and buzzy, a sawtooth sounds bright and rough, and a triangle sits between sine and square. The number shown under One cycle lasts is 1000 divided by the frequency, in milliseconds: at 1000 Hz one cycle takes 1 ms. Sweep glides from one frequency to another once and stops. In the even-per-octave mode every octave takes the same time, which matches how pitch is heard. In the even-per-Hz mode the frequency rises in a straight line. The upper limit of 22,000 Hz is just under half of the 44,100 samples per second that many devices use, the highest frequency such a stream can carry.
What frequency is A4 or middle C?
The note names on this page use equal temperament with A4 set to 440 Hz. In that system each semitone is a factor of 2 to the power of 1/12, so the frequency of a note n semitones above A4 is 440 × 2^(n/12). That gives C4, the note most people call middle C, 261.63 Hz. The notes of octave 4 are C4 261.63, C#4 277.18, D4 293.66, D#4 311.13, E4 329.63, F4 349.23, F#4 369.99, G4 392.00, G#4 415.30, A4 440.00, A#4 466.16 and B4 493.88 Hz. Open Notes in octave 4 and press one to hear it.
For any other frequency the page names the nearest note and how far from it you are, in cents. A cent is one hundredth of a semitone. At 1000 Hz the nearest note is B5 and the tone is 21 cents above it. Many players tune to other values than 440 Hz, and some instruments are tuned in other systems, so the names are a guide to the equal-tempered scale at A4 = 440 Hz, nothing more.
What is a 1000 Hz test tone used for?
A 1000 Hz tone sits in the middle of the range that speakers and headphones play well, so it is a common choice for checking that a speaker or an earphone works, and for checking left and right. Set Speaker to left only and then right only: you should hear the tone from one side at a time. In hearing science 1 kHz is the reference frequency at which the loudness unit called the phon equals the sound level in decibels, according to a peer-reviewed review of the auditory system.
Use the low frequencies to see how low your speakers can go. Small speakers play very low tones poorly, so hearing nothing at 20 Hz tells you about the speakers, not a fault. At the other end, the same review gives the practical frequency range of hearing as 16 Hz to 18 kHz for young healthy listeners, commonly rounded to 20 Hz to 20 kHz. Your own range can be narrower, and it differs from person to person. The page has no claims about healing or health effects of any particular frequency: a frequency is a pitch and nothing else.
Can a tone generator damage speakers or ears?
Yes, if the sound is loud. A constant loud tone is hard on both your ears and small speakers, and square and sawtooth waves are harsher than a sine at the same setting. So the page begins at a low volume, and it fades the sound in over a fraction of a second so it never starts with a click. The volume slider is gentle at the low end, and capped at the top: even at 100% the output is set to half of full scale, 6 dB below the maximum. The default of 10% is about 46 dB below full scale. The warning under the slider turns red at high settings.
How loud it really is depends on your device volume, your speakers or headphones and the room, which the page cannot see. Keep the device volume low at first, raise it slowly, and stop if anything is uncomfortable. Do not use headphones at a high volume. The tone stops when the tab is hidden or you leave the page, so it never plays unattended, and the Stop by itself after choice ends a tone after 5 seconds, 30 seconds, 1 minute or 5 minutes.
Use it with
- Mic Test: check that the microphone works.
- Online Voice Recorder: record and download audio from the mic.
- Webcam Test: check that the camera works.
Questions
How do I play a pure tone at a given frequency?
Type the frequency in Hz (1 to 22,000) and press Play tone, with Sine selected for a pure tone. You can change the frequency while it plays.
What frequency is A4 or middle C?
With A4 at 440 Hz in equal temperament, A4 is 440 Hz and middle C (C4) is 261.63 Hz. The page names the nearest note for any frequency.
What is a 1000 Hz test tone used for?
A 1 kHz tone is a convenient mid-range tone for checking that speakers or headphones work and for checking left and right. It is also the reference frequency for the phon, the loudness unit.
Can a tone generator damage speakers or ears?
Yes, if it is loud. The page starts at a low volume, fades in, caps the maximum at half of full scale and warns at high settings, but you should still raise the volume slowly and stop if it is uncomfortable.
What is the audible frequency range?
A peer-reviewed review gives 16 Hz to 18 kHz for young healthy listeners, commonly rounded to 20 Hz to 20 kHz. Your own range can be narrower.
Why can I hear nothing at a very low or very high frequency?
Small speakers play very low tones poorly, and some people cannot hear the highest tones. Neither means your device is broken. Try other frequencies and the left and right speaker choice.
Sources
How this page was made: the tool's results are computed in your browser by the code on this page, using the sources listed above; the explanations were drafted with AI help and checked against the tool's own output.