Maaz Zindani

Loading the index…

↑↓ move↵ openesc close3993 pages

Free tool · Home and DIY

Roofing calculator

Type the building size or the roof planes and the pitch, and get the roof area, the roofing squares and the bundles of shingles to buy, with a pitch-factor table.

  • Free
  • No sign-up
  • Runs in your browser

By Maaz Zindani · Updated

Units
How do you give the roof size?
Changing it does not convert numbers you already typed.
Pitch (slope)
Extra covers cuts at hips, valleys and edges; complicated roofs need more. One square is 100 ft² (9.29 m²). If your label gives m² per pack, bundles per square = 9.29 ÷ that number.
Result

50 bundles of shingles49.6 exactly · 16.53 squares with 10% extra · 1,502.64 ft² of roof

  • Pitch 6/12 (26.6°)
  • Factor 1.1180
  • 15.03 squares
  • 3 bundles per square
Roofft²
Footprint with overhang: 42 × 32 ft1,344.00
× pitch factor 1.1181,502.64
Roof area1,502.64
Plan area (from above)
1,344.00 ft²
Roof area
1,502.64 ft²
Squares, no extra
15.03
Squares, with 10% extra
16.53
Bundles, exact
49.6
Bundles to buy
50
Ridge length
42 ft
PitchAngleFactorRoof ft²
2/129.5°1.01381,362.54
3/1214.0°1.03081,385.36
4/1218.4°1.05411,416.70
5/1222.6°1.08331,456.00
6/1226.6°1.11801,502.64
7/1230.3°1.15771,555.95
8/1233.7°1.20191,615.29
9/1236.9°1.25001,680.00
10/1239.8°1.30171,749.50
12/1245.0°1.41421,900.70

Formula: pitch factor = √(1 + (rise ÷ 12)²) for a rise per 12, or 1 ÷ cos(angle) for degrees; roof area = plan area × pitch factor; 1 square = 100 ft² (9.29 m²); bundles = squares × (1 + extra ÷ 100) × bundles per square, rounded up.

Your numbers: 42 × 32 × 1.118 = 1,502.64 ft²; ÷ 100 ft² per square = 15.026 squares; × (1 + 10 ÷ 100) = 16.529; × 3 bundles = 49.59, rounds up to 50.

Valleys, dormers, chimneys, skylights, flat sections and a mix of pitches are not modeled: add them as planes and raise the extra. Check the bundles per square and coverage on your shingle's label. Measure from the ground, from drawings or with a professional: do not climb a roof to measure it unless you are trained and equipped.

How to use the Roofing Calculator

  1. Pick US or Metric under Units, then choose Building footprint (length, width and overhang) or Roof planes.
  2. Set the Pitch as Rise per 12 (6 means 6/12) or as an Angle in degrees. Pick the Roof shape if you want the ridge length.
  3. Check the Extra % and the Bundles per square; both are examples you can change.
  4. Read the roof area, squares and bundles under Result, and the pitch table for other slopes.

How do I calculate roof area from the footprint?

A sloping roof is bigger than the building underneath it, by a factor that depends only on the pitch: roof area = plan area × pitch factor. For a rise of x per 12 the factor is √(1 + (x ÷ 12)²), which is 1.118 for a 6/12 roof. A building 40 ft by 30 ft with a 1 ft overhang on every side has a plan area of 42 × 32 = 1,344 square feet, so the roof is 1,344 × 1.118 = 1,502.6 square feet. Gable, hip and shed roofs with the same pitch on every slope all use the same factor, because each slope is stretched by the same amount.

Choose Roof planes when the roof is made of several pieces. Type each plane's width and length, and say whether you measured them along the slope (used as typed) or flat from above (multiplied by the pitch factor). Valleys, dormers, chimneys and flat sections are not modeled, so add each as a plane or raise the extra.

What is a roofing square, and how do I find the pitch?

A roofing square is 100 square feet of roof, which is 9.29 square meters. The example roof of 1,502.6 square feet is 15.03 squares. Shingles, underlayment and flashing are often priced or counted in squares, so it is a handy unit even when you work in meters.

Pitch is how steep the roof is. In the US it is written as rise over a run of 12, so 6/12 means the roof rises 6 inches for every 12 inches across. You can type that, or the angle in degrees: 6/12 is 26.6 degrees and 30 degrees is 6.93/12. Switching between the two converts the number in the box. A roof gets 1.054 times its plan area at 4/12, 1.118 at 6/12 and 1.414 at 12/12, which match a slope correction table published by Owens Corning, and the table under the result lists the factor for each common pitch with the roof area it gives for your building.

How many bundles of shingles do I need?

Multiply the squares by the bundles per square. Owens Corning says its architectural (laminate) shingles are generally packaged at three bundles per square, so the box starts at 3, labelled as an example, because some products come in more bundles per square. Check the label of the shingle you will buy. If your pack label gives an area in square meters, divide 9.29 by that area to get bundles per square.

For the example, 15.03 squares plus 10% extra is 16.53 squares, and 16.53 × 3 = 49.6 bundles, so you buy 50. The exact figure is shown next to the rounded one so you can see how close it is to a whole bundle.

How much waste should I add for hips, valleys and the ridge?

Cutting shingles to fit edges, hips and valleys wastes some of them. The same Owens Corning page recommends adding 10% to 15% to material totals for waste, and says complicated roofs need a higher factor because there are more cuts. The Extra % box starts at 10 as an example: raise it for a roof with many hips, valleys or dormers.

The optional ridge length helps you buy ridge cap. For a gable it is the long side including the overhang, 42 ft in the example. For a hip roof it is the length minus the span, plus four hips, each (span ÷ 2) × √(2 + (rise ÷ 12)²): 10 ft of ridge and 96 ft of hips, 106 ft of cap in all. Measure from the ground or from drawings, and do not climb a roof to measure it unless you are trained and equipped.

Use it with

Questions

How do I calculate roof area from the footprint?

Multiply the plan area, including the overhang, by the pitch factor. A 42 ft by 32 ft footprint at 6/12 pitch is 1,344 × 1.118 = about 1,502.6 square feet of roof.

What is a roofing square?

One roofing square is 100 square feet of roof (9.29 square meters). A roof of 1,502.6 square feet is about 15 squares.

How do I find the pitch of my roof?

Pitch is the rise for every 12 units of run, so 6/12 rises 6 inches over 12 inches. You can also type the angle in degrees. A level and a tape from the attic or drawings gives it without climbing on the roof.

How many bundles of shingles do I need?

Multiply the squares, with extra, by the bundles per square on the label. Owens Corning describes laminate shingles as generally three bundles per square. 16.53 squares × 3 is about 50 bundles.

How much waste should I add for hips and valleys?

Owens Corning suggests 10% to 15% on material totals and more for complicated roofs. The tool starts at 10% as an example, and you can raise it.

Does this cover valleys, dormers and chimneys?

No. It models planes of one pitch. Add each plane of a complex roof as its own row, raise the extra for the cuts, and check with a roofer.

How this page was made: the tool's results are computed in your browser by the code on this page, using the sources listed above; the explanations were drafted with AI help and checked against the tool's own output.