Free tool · Unit and size converters
Torque converter
Type a torque and pick the units: 100 N·m is 73.7562 lb-ft. The converter covers N·m, lb-ft, in-lb, kgf·m and more, and can also work out torque from force and distance.
- Free
- No sign-up
- Runs in your browser
73.7562 lbf·ft100 N·m = 73.7562 lbf·ft
- 1 N·m = 0.737562 lbf·ft
- 1 lbf·ft = 1.35582 N·m
- 1 lbf·ft = 12 lbf·in
- Pound-force feet
73.7562 lbf·ft
Formula: lbf·ft = N·m × 1 ÷ 1.3558179
Your numbers: 100 × 1 ÷ 1.3558179 ≈ 73.7562
| Unit | Value |
|---|---|
| Newton-meters (N·m) | 100 |
| Newton-centimeters (N·cm) | 10,000 |
| Newton-millimeters (N·mm) | 100,000 |
| Kilonewton-meters (kN·m) | 0.1 |
| Kilogram-force meters (kgf·m) | 10.1972 |
| Kilogram-force centimeters (kgf·cm) | 1,019.72 |
| Pound-force feet (lbf·ft, lb-ft) | 73.7562 |
| Pound-force inches (lbf·in, in-lb) | 885.075 |
| Ounce-force inches (ozf·in, oz-in) | 14,161.2 |
Note: This page converts units only. For a bolt, a wheel or any part, use the torque its maker specifies and convert that figure here.
How to use the Torque Converter
- Under What do you want to work out? choose Convert torque, Torque from force or Force from torque.
- To convert, type the number in Torque, then pick From and To. Swap units reverses them.
- For the other two modes, type the force or torque, its unit, the Distance from the axis and the distance unit.
- Set Significant digits, read the answer and the table of every unit, and press Copy to copy the number.
How do I convert Nm to lb-ft and back?
Multiply newton-meters by 0.737562 to get pound-feet (lbf·ft, also written lb-ft). 100 N·m is 73.7562 lbf·ft. To go back, multiply pound-feet by 1.35582: 100 lbf·ft is 135.582 N·m. The two factors are inverses, so dividing by one is the same as multiplying by the other.
The factors are exact, not measured. NIST lists the kilogram-force as exactly 9.80665 newtons, and Handbook 44 lists the pound as exactly 0.45359237 kg and the foot as exactly 0.3048 m. A pound-force is a pound of mass under standard gravity, so 1 lbf = 0.45359237 × 9.80665 = 4.4482216152605 N, and one pound-foot is 4.4482216152605 × 0.3048 = 1.3558179483314 N·m. NIST prints the rounded 1.355 818. The converter keeps every digit and rounds only for display, to the number of significant digits you choose.
A quick check helps catch a factor applied the wrong way round. One pound-foot is a little more than 1.3 N·m, so a torque in N·m is about three quarters of the same torque in lbf·ft. 100 N·m should land a little under 74 lbf·ft, and it does: 73.7562. If going from N·m to lbf·ft gives a bigger number than you typed, the factor was used backwards.
The table lists common sizes in four units. Each row comes from the converter's own factors, so a row matches what the tool shows when you type the same number.
| N·m | lbf·ft | lbf·in | kgf·m |
|---|---|---|---|
| 5 | 3.68781 | 44.2537 | 0.509858 |
| 10 | 7.37562 | 88.5075 | 1.01972 |
| 25 | 18.4391 | 221.269 | 2.54929 |
| 50 | 36.8781 | 442.537 | 5.09858 |
| 100 | 73.7562 | 885.075 | 10.1972 |
| 150 | 110.634 | 1,327.61 | 15.2957 |
| 200 | 147.512 | 1,770.15 | 20.3943 |
| 300 | 221.269 | 2,655.22 | 30.5915 |
| 500 | 368.781 | 4,425.37 | 50.9858 |
What is the difference between lb-ft and in-lb?
A foot is 12 inches, so 1 lbf·ft is 12 lbf·in. The number in in-lb is always 12 times the number in lb-ft for the same torque: 10 lbf·ft is 120 lbf·in, and both are 13.5582 N·m. Mixing them up is a twelvefold error. The converter shows the chip "1 lbf·ft = 12 lbf·in" whenever either unit is chosen, and every result carries its full unit symbol.
An ounce-force inch is one sixteenth of an inch-pound, so 16 oz-in is 1 in-lb, or 0.112984829 N·m. The metric prefixes work the same way: 1 N·m is 100 N·cm and 1,000 N·mm. The second table lists small torques in ozf·in next to four other units.
| ozf·in | N·m | N·cm | lbf·in | kgf·cm |
|---|---|---|---|---|
| 1 | 0.00706155 | 0.706155 | 0.0625 | 0.0720078 |
| 5 | 0.0353078 | 3.53078 | 0.3125 | 0.360039 |
| 10 | 0.0706155 | 7.06155 | 0.625 | 0.720078 |
| 16 | 0.112985 | 11.2985 | 1 | 1.15212 |
| 50 | 0.353078 | 35.3078 | 3.125 | 3.60039 |
| 100 | 0.706155 | 70.6155 | 6.25 | 7.20078 |
What is kgf·m, and how do I convert it?
A kilogram-force meter is the torque of a 1 kg force acting at a distance of 1 m. The kilogram-force is defined as exactly 9.80665 newtons, the standard value of gravity, so 1 kgf·m = 9.80665 N·m and 1 kgf·cm = 0.0980665 N·m, which is 9.80665 N·cm. 10 kgf·m is 98.0665 N·m, or 72.3301 lbf·ft. As a rough check, 1 kgf is close to 10 N, so 1 kgf·m is close to 10 N·m; the exact figure is about 2 percent lower.
The kilogram-force is not an SI unit, and NIST's table converts these torque units to newton-meters. If a tool, a motor label or a manual quotes kgf·m or kgf·cm, convert it here and compare in N·m. Check the symbol carefully: kgf·m and kgf·cm differ by a factor of 100. The kilogram-force is a unit of force, not of mass: a mass of 1 kg weighs 1 kgf only under standard gravity, which is why its newton value is fixed by that definition.
How do I convert torque to force at a given distance?
Divide the torque by the distance from the axis: force = torque ÷ distance. A torque of 100 N·m at 0.5 m needs a force of 200 N. To go the other way, multiply: a 50 lbf push at the end of a 1 ft lever gives 50 lbf·ft, which is 67.7909 N·m. Choose Torque from force or Force from torque, type the numbers and the units, and the page shows the answer with the working. A 0.3 m wrench pulled with 150 N at its end gives 45 N·m, which is 33.1903 lbf·ft, so the wrench or the part can be checked in whichever unit its scale uses.
The formula assumes the force acts at a right angle to the lever. At any other angle only the part of the force at a right angle counts, which is the force times the sine of the angle. The distance runs from the center of the axis to the point where the force acts, so a longer lever gives the same torque for less force: 100 N·m is 328.084 N, or 73.7562 lbf, at 1 ft, 200 N at 0.5 m and 50 N at 2 m.
What torque should I use for a bolt or a wheel?
This page does not give bolt, nut or wheel torque values, and none should be taken from a unit converter. The right figure depends on the fastener, its thread, lubrication, the parts being joined and the maker's specification. Use the number in the manufacturer's manual or the part's documentation, and convert only the unit here, for example from lb-ft in a US manual to N·m for a metric torque wrench.
Check the unit on the number and on the wrench before tightening, especially lb-ft against in-lb, which differ by 12 times. When you note a torque in a log or a message, write the unit with the number and spell out lbf·ft or lbf·in in full instead of a bare "lb", so the next person does not have to guess. For a safety-critical part, follow the maker's procedure or ask a qualified mechanic.
A search for "torque converter" can also lead to a part in an automatic transmission. This page is the unit converter: it changes torque from one unit to another and does not describe vehicle parts.
Use it with
- Dimensional Weight Calculator: volumetric weight for couriers.
- Area Calculator: area of common shapes.
- Volume Calculator: volume of common solids.
Questions
How do I convert Nm to lb-ft?
Multiply by 0.737562, or divide by 1.35582. 100 N·m is 73.7562 lbf·ft.
How do I convert lb-ft to Nm?
Multiply by 1.35582. 100 lbf·ft is 135.582 N·m.
How many in-lb are in a lb-ft?
12, because a foot is 12 inches. 10 lbf·ft is 120 lbf·in.
How do I convert kgf·m to Nm?
Multiply by 9.80665. 10 kgf·m is 98.0665 N·m.
How do I convert torque to force?
Divide the torque by the distance from the axis, with the force at a right angle to the lever. 100 N·m at 0.5 m is 200 N.
What torque should I use for a bolt?
The one in the manufacturer's specification for that bolt and part. This page converts units only and gives no torque specs.
Sources
How this page was made: the tool's results are computed in your browser by the code on this page, using the sources listed above; the explanations were drafted with AI help and checked against the tool's own output.